Creality Space Pi X4L Filament Dryer Box Review (4-Spool)

Affiliate Disclosure: As an Amazon Associate, we earn from qualifying purchases. This post contains affiliate links, and we may earn a commission at no extra cost to you. All prices and discounts mentioned are the Amazon Reference Price as of writing and may change at any time.

Let’s be real: nothing stings like a failed 10-hour print that snaps at layer 400. You check the nozzle, re-level the bed, blame the slicer… and then it hits you. The filament was damp the whole time.

Wet filament is the silent killer of 3D prints. And the Creality Space Pi X4L — a 4-spool filament dryer box — is built to end that problem for good. At $139.00 (Amazon Reference Price, as of writing), it costs less than the spools of ruined PETG sitting in your scrap bin.

Creality Filament Dryer: Quick Specs First

Feature	Creality Space Pi X4L
Capacity	4 spools at once
Max Temperature	85°C
Heating	Dual independent heating chambers
Airflow	Built-in fan circulation
Material Compatibility	PLA, PETG, TPU, ABS, PET, PC, ASA, PA, PAHT and more
Price (Amazon Reference Price, as of writing)	$139.00

Check Price on Amazon →

Space Pi X4L: Why 4 Spools Changes Your Workflow

Most entry-level dryers handle one spool. Maybe two. That’s fine until you’re running a multi-color print, or you want to dry one filament while printing with another. Then you’re stuck playing dryer rotation roulette.

The Space Pi X4L holds four spools at once. Here’s what that means in practice:

• Batch drying: An entire haul of fresh spools gets dried in one session instead of four.
• Print-and-dry simultaneously: Keep two spools feeding a print while the other two bake dry for tomorrow’s job.
• Multi-material setups: PLA in one slot, TPU in another, nylon in a third — all stored dry and ready.

For anyone running more than one printer — or just tired of drying spools one at a time — this capacity alone is a game-changer.

85°C + Dual Heating Chambers: Built for the Tough Materials

Here’s where the X4L separates itself from budget single-zone dryers. It heats up to 85°C with dual independent heating chambers and a fan for air circulation.

Why does that matter? Because not all filaments dry at the same temperature:

• PLA and PETG: forgiving, dry at lower temps
• TPU: needs patience and steady warmth
• Nylon (PA), PC, and PAHT: seriously hygroscopic — they demand higher drying temps and longer cycles

That 85°C ceiling is what makes this box viable for the engineering-grade materials, not just hobby PLA. And the dual-chamber design helps distribute heat evenly across four spools, instead of one weak heater fighting a losing battle.

It also doubles as a filament storage box — leave spools inside between prints and they stay dry instead of slowly soaking up ambient humidity. One purchase, two jobs.

Do You Actually Need a Filament Dryer?

Honest answer: if you live somewhere humid, or print with anything beyond basic PLA, sooner or later — yes.

Signs your filament is wet:

• Stringing and oozing that slicing tweaks won’t fix
• Popping or sizzling sounds at the nozzle (that’s moisture boiling)
• Brittle filament that snaps when unspooled
• Bubbles and rough surface texture on prints
• Prints failing mid-job at random layers

Sounds familiar? The damp spool is probably your culprit — and no amount of slicer tuning will fix moisture baked into the plastic. Drying it properly does.

Who Should Buy the Space Pi X4L?

Grab it if you:

• Print with PETG, TPU, nylon, PC, or ASA regularly
• Run multi-color or multi-printer setups
• Live in a humid climate
• Want to store and dry spools in one device
• Are done blaming your printer for filament problems

Skip it if you:

• Print only occasional small PLA projects in a dry climate (a single-spool dryer might be enough)

Pros & Cons at a Glance

✅ Pros 4-spool capacity — batch dry or print-and-dry at once 85°C max heat handles nylon, PC, and other demanding materials Dual independent heating chambers for even warmth Built-in fan circulation Doubles as long-term filament storage Broad material compatibility (PLA through PAHT)

❌ Cons Overkill (and oversized) for casual single-spool PLA users Takes up dedicated shelf space

Final Verdict: Is the Creality Space Pi X4L Worth It?

For serious hobbyists and anyone printing engineering materials — absolutely. At $139.00 (Amazon Reference Price as of writing), the X4L costs less than two or three premium spools, and it protects every spool you own from that point on.

Failed prints aren’t free. Neither is your time re-printing a 12-hour job. No stress, just dry filament and clean layers — that’s an affordable must-have for any maker’s bench.

Get the Creality Space Pi X4L on Amazon →

FAQ

Q: Can the Space Pi X4L dry all filament types?
A: It’s compatible with a wide range — PLA, PETG, TPU, ABS, PET, PC, ASA, PA (nylon), and PAHT, among others. Each material has its own recommended drying temperature, and the box’s 85°C max covers the demanding ones.

Q: Can I print directly from the dryer box?
A: Yes — that’s one of its core uses. Feed filament from the box straight to your printer so spools stay dry during long prints.

Q: How long does drying take?
A: It depends on the material and how wet it is — PLA may need a few hours, while nylon can take considerably longer. Check the manual’s material chart for specific time and temperature settings.

Q: Is it just a dryer, or also a storage box?
A: Both. Keep spools inside between prints and they’ll stay protected from ambient humidity instead of re-absorbing moisture on an open shelf.